Fluke 107 multimeter: specs
Palm-sized 6000-count digital multimeter for voltage, current to 10 A, resistance, capacitance, frequency, duty cycle and diode test. Rated CAT III 600 V by Fluke.
Specs
| Spec | Value | Source |
|---|---|---|
| DC voltage | 6.000 V, 60.00 V, 600.0 V; accuracy 0.5 % + 3 | source Accuracy Specifications (p.28) |
| AC voltage | 6.000 V, 60.00 V, 600.0 V (40 Hz to 500 Hz); 1.0 % + 3 | source Accuracy Specifications (p.28) |
| Current | 4.000 A and 10.00 A, AC (40 Hz to 200 Hz) and DC; 1.5 % + 3; 10 A duty cycle under 7 minutes on, 20 minutes off at 25 C to 40 C | source Accuracy Specifications (p.31) |
| Resistance | 400.0 ohm to 40.00 Mohm; 0.5 % + 3 to 1.5 % + 3 by range | source Accuracy Specifications (p.29) |
| Capacitance | 50.00 nF to 1000 uF; 2 % + 5 (nF ranges), 5 % + 5 (uF ranges) | source Accuracy Specifications (p.29) |
| Frequency | 50.00 Hz to 100.0 kHz (10 Hz to 100 kHz); 0.1 % + 3 | source Accuracy Specifications (p.30) |
| Safety | IEC 61010-2-033 CAT III 600 V; 600 V maximum between any terminal and earth ground; A input fuse 11 A, 1000 V | source General Specifications (p.25-27) |
| Display | 6000 counts, updates 3 per second | source General Specifications (p.25) |
| Battery | 2 AAA (IEC LR03), 200 hours minimum | source General Specifications (p.25) |
| Operating temperature | 0 C to 40 C (storage -30 C to 60 C) | source General Specifications (p.25-26) |
Power
| Value | Source | |
|---|---|---|
| Supply | 2 x AAA cells | source General Specifications (p.25) |
| Current | 200 hours minimum battery life | source General Specifications (p.25) |
Pinout
We don't publish a pin table for this part: no official source we could verify gives one. Check the labels printed on your module, and see the notes below.
A meter has no header; see the Fluke 106/107 users manual for jack positions.
Build with it
Project ideas for the Fluke 107 multimeter. Each link opens Soldr with the prompt filled in; Soldr assigns the pins, checks power and shows how to wire every part.
- Current draw of an Uno project: Learning measurement task on a low-voltage circuit. The lowest current range is 4.000 A with 1 mA steps, so small currents read coarsely. Place the meter in series only.
- Measure the PWM frequency of an ESP32 pin: The frequency function covers 10 Hz to 100 kHz at 0.1 % + 3 (107 only). A 3.3 V logic output is inside the voltage ranges.
- Component check bench for capacitors and an LDR: The 500.0 nF range covers a 100 nF part (2 % + 5 plus lead capacitance); the resistance ranges cover the LDR. Remove parts from circuits first.
Common mistakes
- Measuring voltage with the leads in the current jack: the A input has an 11 A fuse and very low resistance, so use it in series only (source)
- Using it above its rating: 600 V to earth ground and CAT III 600 V; mains wiring needs a qualified person (source)
- Holding 10 A too long: the 10 A range allows under 7 minutes on and 20 minutes off at 25 C to 40 C (source)
Not covered by the official source
- Product page lists the data sheet only as an HTML page; the user manual is the document used for numbers.