# SS360NT Hall effect sensor: specs and pinout

> A high-sensitivity latching digital Hall-effect sensor IC in a SOT-23 surface-mount package. It switches on when a North pole is applied and stays…

[HTML version](https://soldr.ai/docs/components/ss360nt)

[Docs](https://soldr.ai/docs) / [Components](https://soldr.ai/docs/components)

A high-sensitivity latching digital Hall-effect sensor IC in a SOT-23 surface-mount package. It switches on when a North pole is applied and stays latched until the opposite (South) pole is applied. This is a bare SMD chip, not a breakout module.

Every value cites its sourceOfficial pinout

[Buy on Compoden](https://compoden.com/products/honeywell-ss360nt-hall-effect-sensor-ic-sot-23-3-smd-compoden)

## Specs

| Spec | Value | Source |
|---|---|---|
| Supply voltage | 3.0 to 24.0 V dc (-40 to 125 C); 3.0 to 12.0 V at 150 C | source Table 1 Electrical and Environmental Specifications (p.2) |
| Absolute maximum supply voltage | 26.0 V (and -26.0 V reverse) | source Table 2 Absolute Maximum Specifications (p.2) |
| Supply current | 3.5 mA typ, 6.0 mA max at Vsupply = 3 V, 25 C (8.0 mA max across temperature) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Output type and current | Current-sinking output; 20 mA max output current (abs max 25 mA) | source Figure 1 block diagram (p.3); Tables 1 and 2 (p.2) |
| Output saturation voltage (Vsat) | 0.6 V max at 15 mA with field above 55 gauss (SS360NT) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Magnetic operate point (Bop) | 5 / 30 / 55 gauss (min / typ / max) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Magnetic release point (Brp) | -55 / -30 / -5 gauss (min / typ / max) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Differential (hysteresis) | 40 / 60 / 80 gauss (min / typ / max) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Rise / fall time | 1.5 us max at 25 C | source Table 1 Electrical and Environmental Specifications (p.2) |
| Operating temperature | -40 to 150 C | source Table 1 Electrical and Environmental Specifications (p.2) |
| Pole that turns the output on | North pole (SS360NT); the SS360ST turns on with a South pole | source Description (p.1) |

## Power

| | Value | Source |
|---|---|---|
| Supply | 3.0-24.0 V dc (3.0-12.0 V at 150 C) | source Table 1 Electrical and Environmental Specifications (p.2) |
| Current | 3.5 mA typ at 3 V, 25 C (6.0 mA max) | source Table 1 Electrical and Environmental Specifications (p.2) |

## Pinout

This is the bare SOT-23 chip, so the Honeywell pin drawing applies directly. It has no breakout board; it needs SMD soldering.

| Pin | Function | Voltage | Notes | Source |
|---|---|---|---|---|
| 1 | Vcc (+) | 3.0-24.0 V | Supply | source Figure 5 SOT-23 drawing (p.4) |
| 2 | Output | sinks up to 20 mA | Needs a pull-up; output goes low when a North pole above Bop is applied | source Figure 5 (p.4); Figure 1 (p.3) |
| 3 | Gnd (-) | 0 V | Ground | source Figure 5 SOT-23 drawing (p.4) |

## Build with it
Project ideas for the SS360NT Hall effect sensor. Each link opens Soldr with the prompt filled in; Soldr assigns the pins, checks power and shows how to wire every part.

- [Magnet rotation counter](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20magnet%20rotation%20counter%20with%20an%20Arduino%20Uno%2C%20a%20Honeywell%20SS360NT%20Hall%20sensor%20and%20a%2016x2%20I2C%20LCD): Powered from the Uno 5 V (inside 3-24 V), with the Uno input pull-up on the sinking output. A latching sensor needs alternating poles on the rotor, so mount a North and a South magnet. This is for builders who can solder a SOT-23 part.
- [Magnetic latch indicator](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20magnetic%20latch%20indicator%20that%20sounds%20a%20buzzer%20when%20a%20North%20pole%20is%20brought%20close%2C%20using%20an%20Arduino%20Nano%2C%20a%20Honeywell%20SS360NT%20Hall%20sensor%20and%20an%20active%20buzzer): The output latches on a North pole and releases on a South pole, which makes a simple two-state switch. Learning project, not a security product. This is for builders who can solder a SOT-23 part. The output is current-sinking, so enable INPUT_PULLUP (or add an external pull-up).
- [Magnet-triggered temperature display](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20magnet-triggered%20temperature%20readout%20with%20an%20Arduino%20Uno%2C%20a%20Honeywell%20SS360NT%20Hall%20sensor%2C%20a%20DS18B20%20sensor%20and%20a%2016x2%20I2C%20LCD): A North pole latches the sensor and tells the Uno to show the reading; the DS18B20 sends its value over one wire. Everything runs from the Uno 5 V. This is for builders who can solder a SOT-23 part. The output is current-sinking, so enable INPUT_PULLUP (or add an external pull-up). The DS18B20 data line needs a 4.7 k pull-up to its supply; the resistor pack's values are not listed, so pick the 4.7 k part (yellow, violet, red bands) and confirm it with a multimeter.

## Common mistakes

- Expecting the output to switch off when the magnet is removed: this is a latching sensor that responds to alternating North and South poles, so it holds its state until the opposite pole arrives (source: [link](https://prod-edam.honeywell.com/content/dam/honeywell-edam/sps/siot/zh-cn/products/sensors/magnetic-sensors/latching-position-sensor-ics/common/documents/sps-siot-latching-digital-hall-effect-sensor-ics-ss360nt-ss360st-ss360st-10k-ss460s-ss460s-t2-t3-lp-datasheet-32312441-ciid-143521.pdf), Description p.1)
- Wiring the output without a pull-up: the output is current-sinking (20 mA max), so it pulls low on its own and needs a pull-up resistor or an input pull-up to read a high level (source: [link](https://prod-edam.honeywell.com/content/dam/honeywell-edam/sps/siot/zh-cn/products/sensors/magnetic-sensors/latching-position-sensor-ics/common/documents/sps-siot-latching-digital-hall-effect-sensor-ics-ss360nt-ss360st-ss360st-10k-ss460s-ss460s-t2-t3-lp-datasheet-32312441-ciid-143521.pdf), Figure 1 p.3 and Table 1 p.2)
- Assuming the start-up state is defined: if powered up with a field between Brp and Bop the output can be either ON or OFF; Honeywell recommends allowing 10 us after the supply reaches 5 V for the output to stabilise (source: [link](https://prod-edam.honeywell.com/content/dam/honeywell-edam/sps/siot/zh-cn/products/sensors/magnetic-sensors/latching-position-sensor-ics/common/documents/sps-siot-latching-digital-hall-effect-sensor-ics-ss360nt-ss360st-ss360st-10k-ss460s-ss460s-t2-t3-lp-datasheet-32312441-ciid-143521.pdf), Notice under Table 1 p.2)

## Not covered by the official source

- The Honeywell sheet covers the SS360NT, SS360ST, SS360ST-10K and SS460S family; every value above is from the SS360NT/SS360ST row group.
- Figure 1 labels the output stage 'current sinking'; the sheet does not use the words 'open collector'.
- Check that the stocked reel part marking is SS360NT (the listing title also says Compoden).

## Sources

- [link](https://prod-edam.honeywell.com/content/dam/honeywell-edam/sps/siot/zh-cn/products/sensors/magnetic-sensors/latching-position-sensor-ics/common/documents/sps-siot-latching-digital-hall-effect-sensor-ics-ss360nt-ss360st-ss360st-10k-ss460s-ss460s-t2-t3-lp-datasheet-32312441-ciid-143521.pdf) (Honeywell SS360X & SS460X datasheet, Issue 9, 006015)