# FlySky FS-i6 + FS-iA6B: specs

> A 6-channel 2.4 GHz radio-control transmitter (FS-i6) bundled with a 6-channel receiver (FS-iA6B), both using the maker's AFHDS 2A protocol. The…

[HTML version](https://soldr.ai/docs/components/flysky-fs-i6)

[Docs](https://soldr.ai/docs) / [Components](https://soldr.ai/docs/components)

A 6-channel 2.4 GHz radio-control transmitter (FS-i6) bundled with a 6-channel receiver (FS-iA6B), both using the maker's AFHDS 2A protocol. The maker's page lists fixed-wing, glider, helicopter and boat models.

Every value cites its sourcePinout not published

[Buy on Compoden](https://compoden.com/products/flysky-fs-i6-2-4ghz-6ch-transmitter-with-fs-ia6b-receiver)

## Specs

| Spec | Value | Source |
|---|---|---|
| Transmitter channels and models | 6 channels; model types: fixed wing / glider / helicopter / boat | source FS-i6 specifications |
| Radio | 2.4 GHz, AFHDS 2A, transmission power below 20 dBm, channel resolution 4096 | source FS-i6 specifications |
| Transmitter power | Battery '1.5AA x 4' (maker text; read here as four AA cells); low voltage alarm below 4.2 V; no charging port | source FS-i6 specifications |
| Transmitter display and data port | STN transflective LCD 128x64 dot matrix; data port PS/2 (PPM) | source FS-i6 specifications |
| Transmitter temperature and humidity | -10 C to +60 C; 20% to 95% humidity | source FS-i6 specifications |
| Receiver supply | 4.0 V to 8.4 V | source FS-iA6B specifications |
| Receiver outputs | PWM channels: 6; data port PWM / PPM / i.bus / s.bus; RSSI supported | source FS-iA6B specifications |
| Receiver range | 500 to 1500 m (in the air) | source FS-iA6B specifications |
| Receiver physical | 47 x 26.2 x 15 mm, 10 g; dual copper tube antenna 150 mm x 2 | source FS-iA6B specifications |
| Receiver temperature and humidity | -10 C to +60 C; 20% to 95% humidity | source FS-iA6B specifications |

## Power

| | Value | Source |
|---|---|---|
| Supply | Receiver 4.0 V to 8.4 V; transmitter battery '1.5AA x 4' (maker text, read here as four AA cells) | source FS-iA6B specifications |

## Pinout
We don't publish a pin table for this part: no official source we could verify gives one. Check the labels printed on your module, and see the notes below.

The maker's specification pages list the receiver's output types (PWM, PPM, i.bus, s.bus) but no pin-by-pin table is published, so no pinout is given.

## Build with it
Project ideas for the FlySky FS-i6 + FS-iA6B. Each link opens Soldr with the prompt filled in; Soldr assigns the pins, checks power and shows how to wire every part.

- [Stick position display](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20stick%20position%20display%20that%20reads%20an%20RC%20receiver%20and%20shows%20the%20six%20channel%20values%20on%20an%20OLED%20with%20an%20ESP32): The maker lists PPM and i.bus among the receiver's data ports; which output mode the receiver sends and how to select it are not documented on the pages read here. Power the receiver from a 5 V source within its 4.0 V to 8.4 V range, share ground with the ESP32, and measure the signal level first because the maker gives none. Learning project.
- [RC lamp switch](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20radio-controlled%20lamp%20switch%20where%20an%20RC%20receiver%20channel%20drives%20a%205%20V%20relay%20module%20and%20a%2012%20V%20LED%20strip%20through%20an%20Arduino%20Uno): The Uno measures the channel pulse width and switches the relay input; the relay carries only the low-voltage 12 V strip supply. Check the strip's current against the adapter and do not exceed the relay module's printed DC contact rating. Learning project.
- [RC dimmer for an LED](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20throttle-stick%20LED%20dimmer%20with%20an%20RC%20receiver%2C%20an%20Arduino%20Uno%2C%20a%205%20mm%20LED%20and%20a%20resistor): Reads one receiver channel and sets LED brightness with PWM, so no motor or high current is involved. Power the receiver from the Uno's 5 V pin (inside the 4.0 V to 8.4 V range) and check the signal level. Learning project.

## Common mistakes

- Power the receiver with 4.0 V to 8.4 V only; a 12 V supply is outside the maker's range ([source](https://www.flysky-cn.com/ia6b-canshu)).
- The maker page gives no signal voltage level for the receiver output pins, so measure it before connecting to a 3.3 V board such as the ESP32 (source: [link](https://www.flysky-cn.com/ia6b-canshu), no level stated).
- The receiver range of 500 to 1500 m is 'in the air'; indoors or near the ground it will be shorter, so do a range test before relying on it ([source](https://www.flysky-cn.com/ia6b-canshu)).

## Not covered by the official source

- Only specification pages are available, with no PDF manual, so receiver output voltage level, failsafe settings and pin table are not given.
- Receiver current draw is not stated on the maker's pages.

## Sources

- [link](https://www.flysky-cn.com/ia6b-canshu) (Flysky FS-iA6B specifications page)
- [link](https://www.flysky-cn.com/i6-canshu) (Flysky FS-i6 specifications page)