# 3.7 inch 4-colour e-paper (416x240): specs and pinout

> A 3.7 inch four-colour e-paper panel (red, yellow, black, white) with 416 x 240 pixels and an SPI interface, made by Waveshare as the '3.7inch…

[HTML version](https://soldr.ai/docs/components/e-paper-3-7-inch-4-colour)

[Docs](https://soldr.ai/docs) / [Components](https://soldr.ai/docs/components)

A 3.7 inch four-colour e-paper panel (red, yellow, black, white) with 416 x 240 pixels and an SPI interface, made by Waveshare as the '3.7inch e-Paper HAT+ (G)'. It comes as a raw panel or with a driver board that plugs onto the Raspberry Pi 40-pin header or connects by a 9-pin cable.

Every value cites its sourceOfficial pinout

[Buy on Compoden](https://compoden.com/products/waveshare-3-7inch-e-paper-display-g-416x240-red-yellow-black-white-spi)

## Specs

| Spec | Value | Source |
|---|---|---|
| Display size and resolution | 3.7 inch; 416 x 240 pixels; dot pitch 0.196 mm x 0.196 mm; display area 81.54 mm x 47.04 mm | source Overview > Parameters |
| Display colours | Red, yellow, black, white (2 bits per pixel in the data format) | source Overview > Parameters; Operating Principle |
| Operating voltage | Raw panel: 3.3 V. Driver board: 3.3 V or 5 V, with the I/O level equal to the supply voltage | source Overview > Parameters; notes under 'Operating Principle' |
| Interface | SPI, mode 0 (CPOL 0, CPHA 0); control lines CS, SCL, D/C, SDA, plus RST and BUSY | source Communication Method |
| Refresh time | Fast refresh 12 s; full refresh 20 s (test data from Waveshare, flicker during a full refresh is normal) | source Overview > Parameters |
| Refresh power | Less than 30 mW (typical), test data for one refresh | source Overview > Parameters |
| Operating temperature | 0 to 40 C; storage -25 to 70 C | source Overview > Parameters |
| Outline | Panel 92.99 mm x 53.00 mm x 1.00 mm; driver board 96.00 mm x 57.00 mm | source Overview > Parameters |
| Refresh limits | Refresh at most every 180 s and at least once every 24 hours; put the panel to sleep or cut power when not refreshing | source Notes under 'Operating Principle' |

## Power

| | Value | Source |
|---|---|---|
| Supply | Raw panel 3.3 V; driver board 3.3 V or 5 V (I/O level equal to supply) | source Overview > Parameters (only refresh power, under 30 mW typical, is given; no current figure) |

## Pinout

Pin names and Raspberry Pi wiring are from Waveshare's manual for the 3.7inch e-Paper HAT+ (G) driver board (9-pin cable connection). The raw panel has its own flat-cable connector that this manual does not draw.

| Pin | Function | Voltage | Notes | Source |
|---|---|---|---|---|
| VCC | Power supply | 3.3 V | Wired to Raspberry Pi 3.3 V in the manual's table | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| GND | Ground | | Wired to Raspberry Pi GND | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| DIN | SPI data in (SDA) | | Raspberry Pi MOSI, physical pin 19 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| CLK | SPI clock (SCL) | | Raspberry Pi SCLK, physical pin 23 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| CS | Chip select, active low | | Raspberry Pi CE0, physical pin 24 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| DC | Data/command select: low = command, high = data | | Raspberry Pi BCM 25, physical pin 22 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| RST | Reset | | Raspberry Pi BCM 17, physical pin 11 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| BUSY | Busy status | | Raspberry Pi BCM 24, physical pin 18 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |
| PWR | Power control | | Raspberry Pi BCM 18, physical pin 12 | source Hardware Connection: Raspberry Pi connection pin correspondence (9-pin cable) |

## Build with it
Project ideas for the 3.7 inch 4-colour e-paper (416x240). Each link opens Soldr with the prompt filled in; Soldr assigns the pins, checks power and shows how to wire every part.

- [Pi status board](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20status%20board%20that%20shows%20the%20time%2C%20CPU%20temperature%20and%20uptime%20of%20a%20Raspberry%20Pi%205%20on%20a%203.7%20inch%20red%2C%20yellow%2C%20black%20and%20white%20e-paper%20display): The driver board plugs onto the 40-pin header and uses 3.3 V logic. Refresh at most every few minutes (the manual allows one refresh per 180 s) and sleep the panel in between.
- [Pi Zero daily calendar card](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20daily%20calendar%20and%20weather%20card%20with%20a%20Raspberry%20Pi%20Zero%20W%20and%20a%203.7%20inch%20four-colour%20e-paper%20display): The Zero W has a 3.3 V header and Wi-Fi, so it can fetch the data and redraw once an hour. Red and yellow work for highlights. Keep the refresh interval above 180 s as the manual advises.
- [ESP32 room climate card](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20room%20climate%20card%20with%20an%20ESP32%2C%20a%20BME280%20sensor%20and%20a%203.7%20inch%20four-colour%20e-paper%20display): Use the 9-pin cable connection with the ESP32's 3.3 V pin and SPI pins of your choice. Update the card every 30 minutes and sleep the panel between updates; the 12 s to 20 s refresh is fine for slow-changing readings. The manual's 9-pin table is for a Raspberry Pi; choose the SPI pins on the ESP32 or Pico yourself.
- [Pico meeting-room sign](https://app.soldr.ai/?prompt=I%20want%20to%20build%20a%20meeting-room%20sign%20that%20shows%20free%20or%20busy%20in%20red%20or%20black%20with%20a%20Raspberry%20Pi%20Pico%20and%20a%203.7%20inch%20four-colour%20e-paper%20display): The Pico is a 3.3 V board, matching the raw panel's 3.3 V working voltage. Redraw when the status changes but not more often than every 180 s as the manual advises: hold a change that arrives sooner and redraw later. The manual's 9-pin table is for a Raspberry Pi; choose the SPI pins on the ESP32 or Pico yourself.

## Common mistakes

- Leaving the panel powered or in its active state after a refresh: Waveshare says a long time on high voltage damages the panel permanently, so send the sleep command or cut power after each refresh ([source](https://www.waveshare.com/wiki/3.7inch_e-Paper_HAT+_(G))_Manual, notes under Operating Principle)
- Refreshing too often: the manual recommends at least 180 s between refreshes and a refresh at least every 24 hours, and a 12 s to 20 s refresh means this panel suits status pages, not animation ([source](https://www.waveshare.com/wiki/3.7inch_e-Paper_HAT+_(G))_Manual, Parameters and notes)
- Driving the raw 3.3 V panel from 5 V logic: the manual says the working voltage is 3.3 V and recommends level conversion for a 5 V circuit; on the driver board the I/O level must equal the supply voltage ([source](https://www.waveshare.com/wiki/3.7inch_e-Paper_HAT+_(G))_Manual, Parameters and notes)

## Not covered by the official source

- The display controller chip is not named in the manual, so no controller datasheet is cited.
- The manual covers both the raw panel and the driver-board version; the pin table and the 3.3 V / 5 V rule belong to the driver board.
- No current figure is given other than the refresh power (under 30 mW typical).

## Sources

- [link](https://www.waveshare.com/wiki/3.7inch_e-Paper_HAT+_(G))_Manual (Waveshare wiki, 3.7inch e-Paper HAT+ (G) Manual)
- [link](https://www.waveshare.com/3.7inch-e-paper-hat-plus-g.htm) (Waveshare product page)